https://www.klipper3d.org/Config_checks.html

Basiskonfiguration (Beispiel) für einen Anycubic Mega S ohne Modifikationen / Originalzustand

printer.cfg

# This file contains pin mappings for the Anycubic i3 Mega with
# Ultrabase from 2017. (This config may work on an Anycubic i3 Mega v1
# prior to the Ultrabase if you comment out the definition of the
# endstop_pin in the stepper_z1 section.) To use this config, the
# firmware should be compiled for the AVR atmega2560.
 
# See docs/Config_Reference.md for a description of parameters.
 
[stepper_x]
step_pin: PF0
dir_pin: !PF1
enable_pin: !PD7
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PE5
position_min: -5
position_endstop: -5
position_max: 210
homing_speed: 30.0
 
[stepper_y]
step_pin: PF6
dir_pin: PF7
enable_pin: !PF2
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PL7
position_endstop: 0
position_max: 210
homing_speed: 30.0
 
[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
microsteps: 16
rotation_distance: 8
endstop_pin: ^!PD3
position_endstop: 0.0
position_max: 205
homing_speed: 5.0
 
[stepper_z1]
step_pin: PC1
dir_pin: PC3
enable_pin: !PC7
microsteps: 16
rotation_distance: 8
endstop_pin: ^!PL6
 
[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
microsteps: 16
#rotation_distance: 34.557
rotation_distance: 7.808
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB4
sensor_type: ATC Semitec 104GT-2
sensor_pin: PK5
control: pid
pid_Kp: 15.717
pid_Ki: 0.569
pid_Kd: 108.451
min_temp: 0
max_temp: 245
 
[heater_fan extruder_fan]
pin: PL5
 
[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: pid
pid_Kp: 74.883
pid_Ki: 1.809
pid_Kd: 775.038
min_temp: 0
max_temp: 110
 
[fan]
pin: PH6
 
[mcu]
serial: /dev/ttyUSB0
 
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 10
max_z_accel: 60
 
[heater_fan stepstick_fan]
pin: PH4
 
[virtual_sdcard]
path: ~/gcode_files
 
[display_status]
 
[pause_resume]
 
[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
  TURN_OFF_HEATERS
  CANCEL_PRINT_BASE
 
[gcode_macro START_PRINT]
gcode:
  G28 X0 Y0                     ; move X/Y to min endstops
  G28 Z0                        ; move Z to min endstops
  G1 Z20 Y5 F500                ; move nozzle away from bed
  G92 E0                        ; zero the extruded length
  G1 E2 F2400                    ; extrude 5mm of feed stock
  G92 E0                        ; zero the extruded length again
  M117 Printing...
 
[gcode_macro END_PRINT]
gcode:
  M400                          ; Clear Buffer
  M104 S0                       ; turn off extruder
  M140 S0                       ; turn off bed
  G10                           ; retract
  G91                           ; relative positioning
  G1 E-0.03 Z1.00 X20.0 Y20.0   ; move nozzle to remove stringing
  M106 S0                       ; turn off fan
  G1 Z20                        ; move nozzle up 20mm
  G90                           ; absolute positioning
  G0 X0 Y175                    ; park nozzle at rear
  M84                           ; steppers off
  G4 P250                       ; dwell
  _TIMELAPSE_NEW_FRAME
  M300                          ; Beep